Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 810

Страница: 810 / 2589

Fig. 27: Identifying PCV Valve Hose, PCV Valve Heater Control Connector, PCV Valve, O-Ring &

Torque Specifications

Courtesy of MAZDA MOTORS CORP.

3. Install in the reverse order of removal.

ROLLOVER VALVE REMOVAL/INSTALLATION [MZI-3.7]

ROLLOVER VALVE INSPECTION [MZI-3.7]

1. Perform the fuel tank inspection. (See

FUEL TANK INSPECTION [MZI-3.7]

FUEL SHUT-OFF VALVE REMOVAL/INSTALLATION [MZI-3.7]

NOTE:

The rollover valve cannot be removed as it is built into the fuel tank.

NOTE:

The rollover valve cannot be disassembled and inspected as it is built into

the fuel tank.

NOTE:

The fuel shut-off valve cannot be removed as it is built into the fuel tank.

2008 Mazda CX-9 Grand Touring

2008 ENGINE PERFORMANCE Emission System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:04:04 AM

Page 20

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды