Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 845

Страница: 845 / 2589

Fig. 24: Identifying CMP And PCM Sensor Harness Side Connector

Courtesy of MAZDA MOTORS CORP.

1. Disconnect the PCM connector. (See

PCM REMOVAL/INSTALLATION [MZI-3.7]

2. Inspect the following harness for open or short circuit. (Continuity check)

Open circuit

CMP sensor (RH) terminal A and PCM terminal 2X

CMP sensor (RH) terminal B and PCM terminal 2C

CMP sensor (LH) terminal A and PCM terminal 2AB

CMP sensor (LH) terminal B and PCM terminal 2C

Short circuit

CMP sensor (RH) terminal A and power supply

CMP sensor (RH) terminal A and body ground

CMP sensor (RH) terminal B and power supply

CMP sensor (LH) terminal A and power supply

CMP sensor (LH) terminal A and body ground

2008 Mazda CX-9 Grand Touring

2008 ENGINE Control System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:07:19 AM

Page 27

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды