Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 658 | Manualshive

Страница: 658 / 2589

background image

2. Insert the drive shaft into the joint shaft.
3. After installation, pull the transaxle side outer ring forward to confirm that the drive shaft is securely held

by the clip.

LOCKNUT INSTALLATION NOTE

1. Install a new locknut and stake it as shown.

Fig. 10: Tapping Locknut

Courtesy of MAZDA MOTORS CORP.

FRONT DRIVE SHAFT DISASSEMBLY/ASSEMBLY

1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLES Drive Shaft - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:50:57 AM

Page 7

© 2005 Mitchell Repair Information Company, LLC.

«
...
656
657
658
659
660
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Acdeos Страницы: 7

Бренд: Saab Страницы: 10

Бренд: Wallbox Страницы: 7

Brute Strength 12057.0271

Бренд: Quadratec Страницы: 6

Бренд: Cequent Страницы: 9

Бренд: Ecco Страницы: 9

Бренд: KEKO Страницы: 13

Stealth 4191F Series

Бренд: Road Armor Страницы: 5

Бренд: Mitsubishi MOTORS Страницы: 416

Бренд: Acura Страницы: 6

Бренд: AutoLoc Страницы: 6

2007 SLR Mclaren

Бренд: Mercedes-Benz Страницы: 425

Бренд: HUSKY LINERS Страницы: 4

Бренд: iOttie Страницы: 19

Бренд: Airstream Страницы: 103

Pro Competition

Бренд: G-Tech Страницы: 180

DODGE AD100 1993

Бренд: Chrysler Страницы: 1502

COOPER Convertible

Бренд: Mini Страницы: 168

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды