Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1478

Страница: 1478 / 2589

Fig. 106: View Of No.1 Engine Mount Bolt C

Courtesy of MAZDA MOTORS CORP.

2. Remove the No.1 engine mount bracket bolts A and B as shown.

3. Position the coolant reserve tank out of the way. (See

COOLANT RESERVE TANK

REMOVAL/INSTALLATION [MZI-3.7]

4. Remove the following parts to install the SST.

1. The windshield wiper arm and blade. (See

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION

2. The cowl grille. (See

COWL GRILLE REMOVAL/INSTALLATION

3. The cowl panel. (See

COWL PANEL REMOVAL/INSTALLATION

4. The air cleaner. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-3.7]

5. The front cooler pipe installation bolt (position the front cooler pipe out of the way.).

5. Install the

SST

using the following procedure.

NOTE:

Do not remove the No.1 engine mount rubber from the front

crossmember.

Fig. 107: Identifying No.1 Engine Mount Bracket Bolts

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:57 AM

Page 68

«
...
1476
1477
1478
1479
1480
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды