Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2453

Страница: 2453 / 2589

Fig. 26: Rear Wiper And Washer Switch Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

REAR WIPER ARM AND BLADE REMOVAL/INSTALLATION

1. Remove in the order indicated in the table.

Fig. 27: Identifying Rear Wiper Arm, Blade Components & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

2. Install in the reverse order of removal.
3. Adjust the rear wiper arm and blade. (See

REAR WIPER ARM AND BLADE ADJUSTMENT

REAR WIPER ARM INSTALLATION NOTE

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Wiper/Washer System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:35:20 AM

Page 18

«
...
2451
2452
2453
2454
2455
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды