Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1445

Страница: 1445 / 2589

Fig. 45: Identifying Cylinder Head Cover Bolts (RH)

Courtesy of MAZDA MOTORS CORP.

Fig. 46: Identifying Cylinder Head Cover Bolts (LH)

Courtesy of MAZDA MOTORS CORP.

CYLINDER HEAD COVER OIL SEAL REMOVAL NOTE

1. Tap the OCV attachment hole seals and spark plug tube attachment hole seals using the SSTs and

hammer.

NOTE:

Inspect the OCV attachment hole seals and spark plug tube attachment

hole seals. Remove the any damaged seals.

The OCV attachment hole seals removal is shown, the spark plug tube

attachment hole seals removal procedure is the same.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:57 AM

Page 35

«
...
1443
1444
1445
1446
1447
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды