Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 2589

background image

1. Turn the ignition switch to the LOCK position.
2. Disconnect the negative battery cable and wait for

1 min or more

.

3. Remove the following parts:

1. Front scuff plate inner (See

FRONT SCUFF PLATE REMOVAL/INSTALLATION

.)

2. Rear scuff plate inner (See

REAR SCUFF PLATE REMOVAL/INSTALLATION

.)

3. Front seat belt lower anchor installation bolt (Driver side) (See

FRONT SEAT BELT

REMOVAL/INSTALLATION

.)

4. B-pillar lower trim (See

B-PILLAR LOWER TRIM REMOVAL/INSTALLATION

.)

4. Remove in the order indicated in the table.

Fig. 24: Identifying Side Air Bag Sensor No. 1, Connector & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.
6. Turn the ignition switch to the ON position and hold for

10 s or more

.

7. Verify that the air bag system warning light illuminates for

approx. 6 s

and goes out.

z

If the air bag system warning light does not operate normally, refer to the on-board diagnostic
system (air bag system) and perform inspection of the system. (See

FLOWCHART

.)

SIDE AIR BAG SENSOR NO. 2 REMOVAL/INSTALLATION

1. Turn the ignition switch to the LOCK position.

WARNING:

z

Handling the side air bag sensor improperly can accidentally operate
(deploy) the air bag module, which may seriously injure you. Read

the air bag system service warnings and cautions before handling

the side air bag sensor. (See AIR BAG SYSTEM SERVICE
WARNINGS.) (See AIR BAG SYSTEM SERVICE CAUTIONS.)

WARNING:

z

Handling the side air bag sensor improperly can accidentally operate

(deploy) the air bag module, which may seriously injure you. Read
the air bag system service warnings and cautions before handling

the side air bag sensor. (See AIR BAG SYSTEM SERVICE

WARNINGS.) (See AIR BAG SYSTEM SERVICE CAUTIONS.)

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS Air Bag System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:16:38 AM

Page 21

© 2005 Mitchell Repair Information Company, LLC.

«
...
111
112
113
114
115
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: iDataLink Страницы: 9

Бренд: Warrior Winches Страницы: 17

Бренд: Fabbri Страницы: 4

Бренд: Vintage Air Страницы: 28

Бренд: Kia Страницы: 54

CB-796IG2-CIGD-R

Бренд: CARRYBOY Страницы: 4

Бренд: GMC Страницы: 428

Бренд: minnid Страницы: 44

Quattroporte Automatic

Бренд: Maserati Страницы: 272

Бренд: Honda Страницы: 85

MCL-7000 Series

Бренд: Dakota Digital Страницы: 2

Бренд: Volvo Страницы: 284

Hypercharger HYC 075

Бренд: Alpitronic Страницы: 64

Бренд: SAN HIMA Страницы: 10

Sedan CIVIC 2022

Бренд: Honda Страницы: 701

Parktronic system Volkswagen Golf MK7

Бренд: Car-Systems Страницы: 10

Бренд: v.link Страницы: 12

Бренд: Ford Страницы: 458

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды