Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 870

Страница: 870 / 2589

Fig. 5: Identifying DLC-2

Courtesy of MAZDA MOTORS CORP.

4. Verify the DTC according to the directions on the M-MDS screen.

If any DTCs are displayed, perform troubleshooting according to the corresponding DTC
inspection.

5. After completion of repairs, clear all DTCs stored in the PCM, while referring to "

AFTER REPAIR

PROCEDURE

PENDING TROUBLE CODE ACCESS PROCEDURE

1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initial screen of the M-MDS.

When using the IDS (laptop PC)

1. Select "Self Test".
2. Select "Modules".
3. Select "PCM".

When using the PDS (Pocket PC)

1. Select "Module Tests".
2. Select "PCM".
3. Select "Self Test".

Fig. 6: Identifying DLC-2

2008 Mazda CX-9 Grand Touring

2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:08:34 AM

Page 6

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды