Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1871

Страница: 1871 / 2589

Fig. 5: Identifying Dashboard & Hooks

Courtesy of MAZDA MOTORS CORP.

2. Take the dashboard out through the opened front driver-side door.

DASHBOARD DISASSEMBLY/ASSEMBLY

1. Remove the following parts:

1. Information display (See

INFORMATION DISPLAY REMOVAL/INSTALLATION

2. GPS antenna (See

GPS ANTENNA REMOVAL/INSTALLATION

3. Dashboard garnish (See

DASHBOARD GARNISH REMOVAL/INSTALLATION

4. Hans-free telephone unit (See

HANDS-FREE TELEPHONE (HF/TEL) UNIT

REMOVAL/INSTALLATION

5. Passenger-side air bag module (See

PASSENGER-SIDE AIR BAG MODULE

REMOVAL/INSTALLATION

6. Front speaker (Vehicles With Bose®) (See

FRONT SPEAKER

REMOVAL/INSTALLATION

7. Tweeter (Vehicles Without Bose®) (See

TWEETER REMOVAL/INSTALLATION

8. Center speaker (See

CENTER SPEAKER REMOVAL/INSTALLATION

9. Keyless receiver (See

KEYLESS RECEIVER REMOVAL/INSTALLATION

10. Keyless antenna (See

KEYLESS ANTENNA REMOVAL/INSTALLATION [ADVANCED

KEYLESS SYSTEM]

11. keyless control module (See

KEYLESS CONTROL MODULE REMOVAL/INSTALLATION

[ADVANCED KEYLESS SYSTEM]

12. Auto light-off control module (Vehicles without auto light/wiper system) (See

AUTO LIGHT-

OFF CONTROL MODULE REMOVAL/INSTALLATION

13. Auto light/wiper control module (Vehicles with auto light/wiper system) (See

AUTO

LIGHT/WIPER CONTROL MODULE REMOVAL/INSTALLATION

2. Disassemble in the order indicated in the table.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:25 AM

Page 7

«
...
1869
1870
1871
1872
1873
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды