Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2121

Страница: 2121 / 2589

Fig. 26: Identifying Front Parking Brake Cable And Tab

Courtesy of MAZDA MOTORS CORP.

PARKING BRAKE SWITCH INSPECTION

1. Disconnect the parking brake switch connector.
2. Verify that the continuity is as indicated in the table.

If not as indicated in the table, replace the parking brake switch. (See

PARKING BRAKE

REMOVAL/INSTALLATION [2WD]

.) (See

PARKING BRAKE

REMOVAL/INSTALLATION [AWD]

Fig. 27: Connector Terminal Reference

Courtesy of MAZDA MOTORS CORP.

Fig. 28: Identifying Parking Brake Switch Connector Terminal

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Parking Brake System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:48:01 AM

Page 18

«
...
2119
2120
2121
2122
2123
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды