Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2335

Страница: 2335 / 2589

READING DTCS PROCEDURE

1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

When using the IDS (laptop PC)

1. Select "Self Test".
2. Select "Modules".
3. Select "IC".

When using the PDS (Pocket PC)

1. Select "Module Tests".
2. Select "IC".
3. Select "Self Test".

Fig. 3: Identifying DLC-2 Connector

Courtesy of MAZDA MOTORS CORP.

3. Verify the DTC according to the directions on the screen.

If any DTCs are displayed, perform troubleshooting according to the corresponding DTC
inspection.

4. After completion of repairs, clear all DTCs stored in the instrument cluster. (See

DTC TABLE

[INSTRUMENT CLUSTER]

CLEARING DTCS PROCEDURES

1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

When using the IDS (laptop PC)

1. Select "Self Test".
2. Select "Modules".
3. Select "IC".

When using the PDS (Pocket PC)

1. Select "Module Tests".

2008 Mazda CX-9 Grand Touring

2008 SUSPENSION On-Board Diagnostic (Suspension) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:25:36 AM

Page 3

«
...
2333
2334
2335
2336
2337
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды