Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 203

Страница: 203 / 2589

2. Apply grease to the oil seal lip.
3. Apply ATF to the new seal rings and sliding surface of the oil pump component.

4. Compress the seal rings as shown in the figure. Then install the seal rings to the oil pump component.

Fig. 79: Compressing Seal Rings

Courtesy of MAZDA MOTORS CORP.

5. Apply grease to the thrust washer.

6. Install the thrust washer to the oil pump component.

Fig. 80: Identifying Thrust Washer Of Oil Pump Component

CAUTION:

Do not expand the seal rings too much.

Be careful not to shorten the seal rings too much, when
installing the seal rings.

NOTE:

Verify that oil seal rings rotate smoothly after installing them.

CAUTION:

Apply grease to the mounting surface of the thrust washer so
that it does not drop when installed.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:16 AM

Page 40

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды