Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 2589

background image

1. Dashboard under cover (Passenger side) (See

DASHBOARD UNDER COVER

REMOVAL/INSTALLATION

.)

2. Side wall (See

SIDE WALL REMOVAL/INSTALLATION

.)

3. Console panel (Passenger side) (See

CONSOLE PANEL REMOVAL/INSTALLATION

.)

5. Remove the connector.
6. Remove the nuts.
7. Remove the SAS control module in the direction of the arrow
8. Install in the reverse order of removal.
9. Turn the ignition switch to the ON position.

z

If the SAS control module is replaced, turn the ignition switch to the ON position for

20 s or more

after completing the configuration.

10. Verify that the air bag system warning light illuminates for

approx. 6 s

and goes out.

z

If the air bag system warning light does not operate, refer to the on-board diagnostic system (air

bag system) and perform inspection of the system. (See

FLOWCHART

.)

Fig. 19: Identifying SAS Control Module, Connector & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

SAS CONTROL MODULE CONFIGURATION.

1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

z

When using the IDS (laptop PC)

1. Select "Module Programming".

NOTE:

z

Use the IDS (laptop PC) because the PDS (Pocket PC) does not support

the SAS CONTROL MODULE CONFIGURATION.

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS Air Bag System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:16:38 AM

Page 17

© 2005 Mitchell Repair Information Company, LLC.

«
...
107
108
109
110
111
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Titanium Series

Бренд: Fass Страницы: 13

PRIME DESIGN VCR 326

Бренд: Safe Fleet Страницы: 16

Prime Design VBC PC11

Бренд: Safe Fleet Страницы: 8

Prime Design AR1418

Бренд: Safe Fleet Страницы: 4

Бренд: Ultra Start Страницы: 8

Бренд: Cargo Floor Страницы: 16

Бренд: FAAFTECH Страницы: 8

Бренд: AutoMaxi Страницы: 2

Бренд: BMW Страницы: 189

Бренд: Subaru Страницы: 298

Бренд: v.link Страницы: 12

Interlock 700 Series

Бренд: Scania Страницы: 82

Бренд: Painless Performance Страницы: 16

Бренд: EUFAB Страницы: 8

2014 All vehicles

Бренд: Jeep Страницы: 44

Бренд: Pet Gear Страницы: 4

2018 GRAND CHEROKEE

Бренд: Jeep Страницы: 372

Бренд: Chevrolet Страницы: 324

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды