Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 370

Страница: 370 / 2589

5. Set the adjustable wrench as shown in the figure to hold the manual shaft lever.

Fig. 41: Identifying Manual Shaft Lever

Courtesy of MAZDA MOTORS CORP.

6. Remove the manual shaft nut and washer.

Fig. 42: Identifying Manual Shaft Nut & Washer

Courtesy of MAZDA MOTORS CORP.

7. Remove the TCM.

Fig. 40: Identifying Manual Shaft Lever & TCM Connector

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:30 AM

Page 42

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды