Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1931

Страница: 1931 / 2589

Fig. 19: Identifying Front Fog Light Bulb & Connector

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

FRONT FOG LIGHT BULB REMOVAL NOTE

1. Remove the front fog light bulb by turning it in the direction shown by the arrow.

FRONT SIDE TURN LIGHT REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the inner garnish. (See

INNER GARNISH REMOVAL/INSTALLATION

3. Remove the front door trim. (See

FRONT DOOR TRIM REMOVAL/INSTALLATION

4. Remove the power outer mirror. (See

POWER OUTER MIRROR REMOVAL/INSTALLATION

5. Install in the reverse order of removal.

CAUTION:

A halogen bulb generates extremely high heat when it is

illuminated. If the surface of the bulb is soiled, excessive heat

will build up and the life of the bulb will be shortened. When
handling the bulb, hold the flange, not the glass.

Fig. 20: Identifying Front Fog Light Bulb

Courtesy of MAZDA MOTORS CORP.

NOTE:

Front side turn lights are integrated with the power outer mirror.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:06 AM

Page 15

«
...
1929
1930
1931
1932
1933
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды