Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 482

Страница: 482 / 2589

DIAGNOSTIC PROCEDURE

DTC C1194, C1198, C1210, C1214, C1242, C1246, C1250, C1254, C1404, C1410, C1957, C1958

[DSC/RSC] DIAGNOSTIC PROCEDURE

DTC C1242

LR outlet solenoid valve system

DTC C1246

RR outlet solenoid valve system

DTC C1250

LR inlet solenoid valve system

DTC C1254

RR inlet solenoid valve system

DTC C1404

RH traction control solenoid valve system

DTC C1410

LH traction control solenoid valve system

DTC C1957

RH stability control solenoid valve system

DTC C1958

LH stability control solenoid valve system

DETECTION

CONDITION

Solenoid valve operation does not correspond to solenoid ON/OFF
commands from the DSC/RSC HU/CM.

POSSIBLE CAUSE

Open or short circuit in the DSC/RSC HU/CM internal solenoid valves

Solenoid valve malfunction

Poor connection at connectors (female terminal)

STEP

INSPECTION

ACTION

VERIFY DTC INSPECTION

Turn the ignition switch off.

Connect the M-MDS to the DLC-2.

Turn the ignition switch to the ON

position (engine off).

Clear the DTC from the memory.

(See

ON-BOARD DIAGNOSTIC

[DSC/RSC]

Re-perform the DTC inspection.

Is more than one solenoid valve-related

DTC output?

Yes Go to the next step.

Replace the DSC/RSC HU/CM, then go to the

Step 3.

(See

DSC/RSC HU/CM

REMOVAL/INSTALLATION

INSPECT DSC/RSC HU/CM POWER
SUPPLY AND GROUND CIRCUIT FOR

OPEN CIRCUIT

Measure the voltage between DSC/RSC
HU/CM terminal AL and terminal A.

Is the voltage more than 10 V?

Yes

Replace the DSC/RSC HU/CM, then go to the
next step.

(See

DSC/RSC HU/CM

REMOVAL/INSTALLATION

Repair or replace the wiring harness, then go

to the next step.

VERIFY DTC TROUBLESHOOTING
COMPLETED

Repeat the inspection from Step 1.

2008 Mazda CX-9 Grand Touring

2008 BRAKES On-Board Diagnostic (DSC/RSC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:50:13 AM

Page 26

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды