Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 564

Страница: 564 / 2589

Courtesy of MAZDA MOTORS CORP.

Rectifier (Using an analog circuit tester)

1. Inspect for continuity of the diodes using an analog circuit tester.

If not as specified, replace the rectifier.

Specification

CONTINUITY SPECIFICATION

Fig. 15: Identifying Rectifier

Courtesy of MAZDA MOTORS CORP.

Rectifier (Using a digital circuit tester)

1. Inspect for continuity of the diodes using a digital circuit tester.

If not as specified, replace the rectifier.

Specification

CONTINUITY SPECIFICATION

Bearing

Negative

Positive

Continuity

P1, P2, P3, P4, P5, P6

Yes

P1, P2, P3, P4, P5, P6

Yes

Negative

Positive

Continuity

P1, P2, P3, P4, P5, P6

Yes

P1, P2, P3, P4, P5, P6

Yes

2008 Mazda CX-9 Grand Touring

2008 ENGINE Charging System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:54:58 AM

Page 14

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды