Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1872 | Manualshive

Страница: 1872 / 2589

background image

3. Assemble in the reverse order of disassembly.

Fig. 6: Identifying Dashboard Wiring Harness, Member & Dashboard Face

Courtesy of MAZDA MOTORS CORP.

COLUMN COVER REMOVAL/INSTALLATION

LOWER COLUMN COVER

1. Remove the screws.
2. Pull down the tilt wheel release lever.
3. Remove the lower column cover in the direction of the arrow.
4. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:25 AM

Page 8

© 2005 Mitchell Repair Information Company, LLC.

«
...
1870
1871
1872
1873
1874
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Camcar Страницы: 6

Бренд: Yakima Страницы: 8

Бренд: Kia Страницы: 385

Бренд: EUFAB Страницы: 52

Parktronic system Volkswagen Golf MK7

Бренд: Car-Systems Страницы: 10

Park Vision VAL632210

Бренд: Valeo Страницы: 25

Бренд: Draw tite Страницы: 4

Бренд: EFILive Страницы: 25

Бренд: Acura Страницы: 19

Бренд: Ford Страницы: 325

Бренд: Ford Страницы: 4378

Бренд: Toyota Страницы: 549

Halo Pole Mount

Бренд: Charge Amps Страницы: 14

MULTI VEHICLE MOUNT MVM-45-05

Бренд: Bracketron Страницы: 4

Бренд: Whelen Engineering Company Страницы: 2

Бренд: Ferrari Страницы: 45

Бренд: Edscha Trailer Systems Страницы: 42

Бренд: Blueant Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды