Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2005

Страница: 2005 / 2589

Fig. 56: Inserting Screwdriver Into Transmitter Notch & Transmitter

Courtesy of MAZDA MOTORS CORP.

3. Remove the battery.

Fig. 57: Removing Battery

Courtesy of MAZDA MOTORS CORP.

4. Install the new battery (CR1620) with the positive pole facing down.
5. Align the upper and lower cover and close the transmitter.

Used battery

Lithium battery CR1620

Battery life

Approx. 2 years (when used 10 times/day)

6. Install the key to the transmitter.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:58 AM

Page 35

«
...
2003
2004
2005
2006
2007
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды