Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1967

Страница: 1967 / 2589

CONSOLE

1. Disconnect the negative battery cable.
2. Remove the front map light. (See

FRONT MAP LIGHT REMOVAL/INSTALLATION

3. Remove in the order indicated in the table.

Fig. 81: Identifying Console Indirect Illumination & Connector

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

FRONT DOOR POCKET

1. Disconnect the negative battery cable.
2. Remove the front door trim. (See

FRONT DOOR TRIM REMOVAL/INSTALLATION

3. Remove the handle pull. (See

FRONT DOOR TRIM DISASSEMBLY/ASSEMBLY

4. Remove in the order indicated in the table.

Fig. 82: Identifying Front Door Pocket Indirect Illumination, Cover & Connector

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

FRONT DOOR POCKET INDIRECT ILLUMINATION REMOVAL NOTE

1. Open the cover in the direction of the arrow and remove the front door pocket indirect illumination.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:06 AM

Page 51

«
...
1965
1966
1967
1968
1969
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды