Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1829 | Manualshive

Страница: 1829 / 2589

background image

1. Level the vehicle.
2. Complete the "BEFORE SERVICE PRECAUTION". (See

BEFORE SERVICE PRECAUTION [MZI-

3.7]

.)

3. Disconnect the negative battery cable.
4. Remove the engine cover. (See

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.7]

.)

5. Remove the fuel line schrader valve cap.
6. Connect a long hose to the disconnected schrader valve cap and drain the fuel into a container used for

collecting gasoline.

Fig. 8: Identifying Fuel Line Schrader Valve Cap & Fuel Distributor

Courtesy of MAZDA MOTORS CORP.

7. Start the fuel pump using the following procedure.

Using M-MDS

1. Connect the negative battery cable.
2. Connect the M-MDS to the DLC-2.
3. Using the simulation function "FP", start the fuel pump.

Without using M-MDS

1. Insert a flathead screwdriver into tab part of the check connector and remove the check connector

cap.

CAUTION:

z

Connecting to the wrong check connector terminal may
only to cause malfunction. Carefully connect the specified

terminal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:42:27 AM

Page 19

© 2005 Mitchell Repair Information Company, LLC.

«
...
1827
1828
1829
1830
1831
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: FABBRI PORTATUTTO Страницы: 2

Бренд: Ford Страницы: 12

Wallbox eM4 Single

Бренд: ABL Страницы: 68

Бренд: Metra Electronics Страницы: 2

Chevrolet Silverado 2500HD 2021

Бренд: GMC Страницы: 433

Бренд: Atera Страницы: 10

4500 CHASSIS CAB 2012

Бренд: RAM Страницы: 7

Бренд: Alfa Romeo Страницы: 8

Бренд: JKS Страницы: 3

Бренд: Mazda Страницы: 122

Бренд: Whelen Engineering Company Страницы: 9

Бренд: KEKO Страницы: 3

Бренд: Movon Страницы: 43

Бренд: Guidosimplex Страницы: 8

PRIME DESIGN VCR-TC11B

Бренд: Safe Fleet Страницы: 12

Бренд: Roadmaster Страницы: 4

Бренд: Connects2 Страницы: 2

transit connect 2012

Бренд: Ford Страницы: 299

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды