Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1840 | Manualshive

Страница: 1840 / 2589

background image

BLIND SPOT MONITORING (BSM) CONTROL MODULE
REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the rear combination light. (See

REAR COMBINATION LIGHT

REMOVAL/INSTALLATION

.)

3. Remove the rear bumper. (See

REAR BUMPER REMOVAL/INSTALLATION

.)

4. Pull the connector in the direction shown by the arrow (2) in the+ figure and remove it while pressing the

tab in the direction shown by arrow (1).

5. Remove the nuts.
6. Remove the BSM control module.
7. Install in the reverse order of removal.
8. Perform the blind spot monitoring radar test. (See

BLIND SPOT MONITORING (BSM

) RADAR

TEST.)

Fig. 16: View Of Blind Spot Monitoring Control Module & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

BLIND SPOT MONITORING (BSM) CONTROL MODULE INSPECTION

1. Remove the trunk box. (See

TRUNK BOX REMOVAL/INSTALLATION

.)

2. Remove the seat side box. (BSM control module (LH) only) (See

SEAT SIDE BOX

REMOVAL/INSTALLATION

.)

3. Remove the trunk end trim. (BSM control module (LH) only) (Vehicles with Bose®) (See

TRUNK END

All segments and dots illuminated. LCD is normal.
Except above

Replace the information display.

CAUTION:

z

If the BSM control modules are installed with the left and right

modules reversed, a DTC will be displayed and system will enter the

fail-safe function. Therefore, confirm that the left/right BSM control
modules are installed correctly.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:42:27 AM

Page 30

© 2005 Mitchell Repair Information Company, LLC.

«
...
1838
1839
1840
1841
1842
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Pacbrake Страницы: 9

Бренд: Kargo Master Страницы: 6

Бренд: Daewoo Страницы: 68

Бренд: Hyundai Страницы: 437

Бренд: Mercedes-Benz Страницы: 30

5TH GEN 4RUNNER

Бренд: Victory 4x4 Страницы: 5

Бренд: Keith Страницы: 2

Бренд: BMW Страницы: 21

Бренд: Volvo Страницы: 24

Бренд: Cadillac Страницы: 20

Бренд: Kuda Страницы: 2

Бренд: Quadratec Страницы: 12

Бренд: Camecho Страницы: 2

E60-82-007-02-10

Бренд: Eibach Страницы: 3

Бренд: Linear Logic Страницы: 8

Бренд: Broadfeet Страницы: 2

Бренд: MBRP Страницы: 5

Бренд: Scosche Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды