background image

Register your  product onllne  at 

www.scosche.com/register 

HAQ02 

2006-11  Honda Civic 

Qi Center Console Direct Fit Bezel 

PARTS  INCLUDED 

1.  (1) Direct Fit Bezel w/ MQUSM 

2.  (1) Vehicle Specific T-harness 

3.  (2) MAGICPLATE'" 

4.  (2) MAGICPLATE'" Applicator 

5.  (6) Double-sided Adhesive 

READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS MOUNT KIT. 

WARNING:  Do not use the magnetic mount with any hard-drive based devices such 

as: iPod classic, iPod Video and Zune MP3 players.  Use caution whenever removing 

or handling plastic parts of any vehicle. Unnecessary force or pressure can cause pieces 

to crack or break. Please use a plastic card to remove the metal plates. Remove adhesive 

residue with a non-abrasive cleaner. 

CAUTION: This magnetic device is not  a toy. The small magnets are harmful if swallowed. 

Keep away from children. 

PRELIMINARY INTRODUCTION 

Wirelessly charge your Qi-enabled smartphone without the need to plug your device into 

a  car  charger  or  USB  cable.  Quickly  charge  your  device  at  5W  or  1 OW  charging.  The 

high powered neodymium magnets are 100% safe and will not damage your device. The 

HAQ02 works with Qi-enabled smartphones from these manufacturers: Apple, Samsung, 

Google, Microsoft,  LG, HTC, Motorola. Also works with Qi-enabled cases, receivers, and 

battery covers. 

CAUTION: 

Disconnect your  vehicles  negative  battery terminal  before  the  installation  to  help 

prevent electrical damage.  We recommend the use of a volt/ ohm meter over a test light to check 

wiring. A test or grounded wire probe can cause damage to the vehicle's computer and/or diagnostic 

system. Avoid all factory airbag wiring 

-

airbags can accidentally deploy causing serious injury or 

death. 

NOTE: See your vehicle's instructions for any special tools your installat1on might require. 

IMPORTANT! DO NOT RETURN PRODUCT TO THE RETAILER. If you need assistance or replacement parts contact us at: 

1 ·800-363-4490 X1  I 

��---

,

.•.. -� 

www.scosche.com/contact. Our office hours are: Mon-Fri: 8AM-5:30PM (Psn and Sat: 8AM-2PM (PSn 

This instruction booklet is based on carefully  documented data and research of automobile disassembly, wire harness 

and  information  pertaining  to  the  installation  of  this  kit.  Scosche  Industries,  Inc.  cannot  be  held  responsible  for 

discrepancies/ inconsistencies that may  occur due to the automobile manufacturing changes or options, or damages 

that may occur in the automobile during the installation of components while using this booklet. 

©2018 SCOSCHE INDUSTRIES, INC 

HAQ02 05/19 

Содержание HAQ02









Отзывы: