Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 293

Страница: 293 / 2589

Tightening torque 7.8 - 11.8 N.m {82 - 122 kgf.cm, 72 - 105 in.lbf}

Fig. 235: Identifying Oil Cooler Outlet Tube, Pipe Clamp, Transaxle Case No. 1 Plate And Wiring

Harness Clip

Courtesy of MAZDA MOTORS CORP.

26. Connect the VSS wiring harness to the wiring harness clip.

Fig. 236: Identifying Wiring Harness Clip

Courtesy of MAZDA MOTORS CORP.

27. Apply ATF to the bearing and gear of the differential component.

Do not damage the VSS wiring harness.

Do not pull hard on the VSS wiring harness.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:17 AM

Page 130

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды