Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 843

Страница: 843 / 2589

2. Inspect the following harness for open or short circuit. (Continuity check)

Open circuit

CKP sensor terminal A and PCM terminal 2P

CKP sensor terminal B and PCM terminal 2T

Short circuit

CKP sensor terminal A and power supply

CKP sensor terminal A and body ground

CKP sensor terminal B and power supply

CKP sensor terminal B and body ground

CAMSHAFT POSITION (CMP) SENSOR REMOVAL/INSTALLATION [MZI-3.7]

1. Disconnect the negative battery cable.
2. Remove the battery.
3. Remove the following part for easier access.

Remove the resonance chamber and air cleaner assy. (See

INTAKE-AIR SYSTEM

REMOVAL/INSTALLATION [MZI-3.7]

4. Disconnect the CMP sensor connector
5. Remove the CMP sensor.

6. Install in the reverse order of removal.

Fig. 23: Identifying CMP Sensor Connector & Torque Specifications

NOTE:

Lubricate the CMP O-ring seal with clean engine oil.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Control System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:07:19 AM

Page 25

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды