Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 400

Страница: 400 / 2589

14. Fix the VSS wiring harness and input/turbine speed sensor wiring harness with tape to the transaxle case

as shown in the figure.

Fig. 95: Locating VSS Wiring Harness & Input/Turbine Speed Sensor Wiring Harness

Courtesy of MAZDA MOTORS CORP.

15. Remove the suction cover and the gasket.

16. Remove the control valve body installation bolts.

NOTE:

Be sure to secure the VSS and input/turbine speed sensor with tape
so that they will not interfere with the control valve body component.

CAUTION:

Evenly loosen the bolts a little at a time in the order shown in

the figure.

Fig. 96: Identifying Suction Cover & Gasket
Courtesy of MAZDA MOTORS CORP.

CAUTION:

Do not drop the control valve body component.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:31 AM

Page 72

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды