Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2386

Страница: 2386 / 2589

Fig. 9: Identifying Front Power Window Regulator Nuts & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

4. Insert a hand through the speaker installation hole, rotate the drum housing in the direction shown in the

figure to detach the tabs from the front door module.

Fig. 10: Rotating Drum Housing

Courtesy of MAZDA MOTORS CORP.

5. Move the front power window regulator in the direction of the arrow and remove it.
6. Install in the reverse order of removal.

REAR POWER WINDOW REGULATOR REMOVAL/INSTALLATION

CAUTION:

Make sure the cable does not unspool from the drum housing

when installing.

Fig. 11: Identifying Front Power Window Regulator

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 7

«
...
2384
2385
2386
2387
2388
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды