Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 652

Страница: 652 / 2589

2008 DRIVELINE/AXLES

Drive Shaft - Mazda CX-9

DRIVE SHAFT LOCATION INDEX

Fig. 1: Identifying Drive Shaft Component Location

Courtesy of MAZDA MOTORS CORP.

FRONT DRIVE SHAFT PRE-INSPECTION

1. Inspect the dust boot on the drive shaft for cracks, damage, leaking grease, and looseness in the boot

band.

2. Inspect the drive shaft for bends, cracks, and wear in the joint or splines.

Repair or replace the drive shaft or boot/band as necessary.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLES Drive Shaft - Mazda CX-9

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLES Drive Shaft - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:50:57 AM

Page 1

Microsoft

Sunday, November 15, 2009 9:51:02 AM

Page 1

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды