Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1526

Страница: 1526 / 2589

Fig. 40: Front Antenna Feeder Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 41: Identifying Front Antenna Feeder Terminals

Courtesy of MAZDA MOTORS CORP.

REAR ANTENNA FEEDER INSPECTION

1. Verify that the continuity is as indicated in the table.

If not as indicated in the table, replace the rear antenna feeder.

Fig. 42: Rear Antenna Feeder Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 43: Identifying Rear Antenna Feeder Terminals

Courtesy of MAZDA MOTORS CORP.

GPS ANTENNA FEEDER INSPECTION

1. Verify that the continuity is as indicated in the table.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Entertainment - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:06 AM

Page 26

«
...
1524
1525
1526
1527
1528
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды