Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 402

Страница: 402 / 2589

Fig. 99: Locating Separate Plate

Courtesy of MAZDA MOTORS CORP.

2. Temporarily install the control valve body component with the bolts.

Bolt length (measured from below the head)

A: 31 mm {1.220 in}

B: 17 mm {0.669 in}

C: 21 mm {0.827 in}

3. Temporarily install the suction cover and a new gasket with the bolts.

NOTE:

Aligning the bolt holes, temporarily tighten the bolt by hand.

Fig. 100: Locating Control Valve Body Component With Bolts
Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:31 AM

Page 74

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды