Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1428

Страница: 1428 / 2589

Fig. 20: Locating Camshaft Timing Chain Mark (LH)

Courtesy of MAZDA MOTORS CORP.

4. Remove the timing chain in the following order.

1. Chain tensioner
2. Timing chain
3. Tensioner arm
4. Chain guide

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:57 AM

Page 18

«
...
1426
1427
1428
1429
1430
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды