Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 832 | Manualshive

Страница: 832 / 2589

background image

VOLTAGE INSPECTION

1. Remove the MAF sensor with the connector still connected.
2. Turn the ignition switch to the ON position.
3. Verify that the MAF sensor output voltage (M-MDS monitor item: MAF) changes when wind is

introduced gradually to the sensor part of the MAF sensor.

z

If it cannot be verified even though the related harnesses have no malfunction, replace the MAF

sensor. (See

MASS AIR FLOW (MAF)/INTAKE AIR TEMPERATURE (IAT) SENSOR

REMOVAL/INSTALLATION [MZI-3.7]

.)

z

If the monitor item status/specification (reference) is not within the specification, even though the

resistance is within the specification, perform the "Circuit Open/Short Inspection".

CIRCUIT OPEN/SHORT INSPECTION

Fig. 11: Identifying MAF/IAT Sensor And PCM Wiring Harness Side Connector

Courtesy of MAZDA MOTORS CORP.

1. Disconnect the PCM connector. (See

PCM REMOVAL/INSTALLATION [MZI-3.7]

.

2. Disconnect the MAF/IAT sensor connector.
3. Inspect the following wiring harnesses for open or short. (Continuity inspection)

2008 Mazda CX-9 Grand Touring

2008 ENGINE Control System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:07:19 AM

Page 14

© 2005 Mitchell Repair Information Company, LLC.

«
...
830
831
832
833
834
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: LaserTrack Страницы: 12

Бренд: Vaisala Страницы: 24

Бренд: Vauxhall Страницы: 2

Бренд: Aries Страницы: 3

Бренд: Vintage Air Страницы: 28

Ride-Rite Air Helper Springs 2173

Бренд: Firestone Страницы: 4

Q Access Alpha GSE 2023

Бренд: Q Mobility Group Страницы: 9

2010 Civic Sedan

Бренд: Honda Страницы: 390

Бренд: A-Tach Страницы: 2

Бренд: Baja Designs Страницы: 5

BEDXTENDER HD MAX 74841-00A

Бренд: AMP Research Страницы: 9

Бренд: Belkin Страницы: 2

Бренд: v.LOGiC Страницы: 22

Бренд: NavInc Страницы: 6

Denali 1094-0185-15

Бренд: E&G Classics Страницы: 3

Бренд: Metra Electronics Страницы: 2

Бренд: ECS Страницы: 4

Бренд: Whispbar Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды