Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 377

Страница: 377 / 2589

Substitution SST

49 F026 102

Outer diameter: 27 mm {1.06 in} or more

Inner diameter: 15-18 mm {0.60-0.70 in}

6. Install the TCM. (See

TCM REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

7. Install the air cleaner component. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.7]

8. Connect the negative battery cable.

Fig. 55: Tapping Oil Seal

Courtesy of MAZDA MOTORS CORP.

AUTOMATIC TRANSAXLE REMOVAL/INSTALLATION [AW6A-EL, AW6AX-

EL]

1. Disconnect the negative battery cable.
2. Remove the following parts.

1. Battery and battery tray (See

BATTERY REMOVAL/INSTALLATION [MZI-3.7]

2. Air cleaner component (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.7]

3. Engine cover
4. Windshield wiper arm and blade (See

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION

5. Cowl grille (See

COWL GRILLE REMOVAL/INSTALLATION

6. Cowl panel (See

COWL PANEL REMOVAL/INSTALLATION

7. Front wheel
8. Splash shield
9. Side cover

10. Propeller shaft (transfer side) (See

PROPELLER SHAFT REMOVAL/INSTALLATION

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:31 AM

Page 49

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды