Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1423 | Manualshive

Страница: 1423 / 2589

background image

3. Mark the crank pulley and engine front cover as shown in the figure.
4. Rotate the crankshaft clockwise 360 ° so that the No.5 cylinder is at TDC of the compression

stroke.

5. Measure the valve clearance of location B shown in the figure.

z

If it is not within the specification, replace the tappet and adjust the valve clearance to the
median value of the standard.

Fig. 15: Locating Crank Pulley Mark

Courtesy of MAZDA MOTORS CORP.

Standard valve clearance [Engine cold]

IN: 0.150-0.250 mm {0.00591-0.00984 in}

Fig. 14: Identifying Engine Front Side
Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:57 AM

Page 13

© 2005 Mitchell Repair Information Company, LLC.

«
...
1421
1422
1423
1424
1425
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

KO PROPO RTF 2002 ESC

Бренд: Tamiya Страницы: 2

Бренд: Toyota Страницы: 56

Бренд: Roav Страницы: 10

Бренд: Car-Interface Страницы: 23

Бренд: RuggON Страницы: 2

Бренд: Wagan Страницы: 8

Бренд: Thermo King Страницы: 2

Бренд: Brodit Страницы: 2

5TH GEN 4RUNNER

Бренд: Victory 4x4 Страницы: 5

Бренд: Keith Страницы: 2

Бренд: IBASE Technology Страницы: 100

S2000 Windscreen Camera Mount

Бренд: Modifry Products Страницы: 2

Бренд: Rago FABRICATION Страницы: 10

Бренд: BMW Страницы: 55

Бренд: Whispbar Страницы: 15

Бренд: Park-Daddy Страницы: 22

Electra 225 1965

Бренд: Buick Страницы: 914

Бренд: Edelbrock Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды