Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 123

Страница: 123 / 2589

Fig. 39: Connecting SST (Deployment Tool) To SST (Adapter Harness)

Courtesy of MAZDA MOTORS CORP.

7. Press the activation switch on the

SST (Deployment tool)

to operate (deploy) the side air bag module.

8. Disconnect the

SSTs (Deployment tool)

from the

SSTs (Adapter harness)

Fig. 40: Identifying Activation Switch

Courtesy of MAZDA MOTORS CORP.

CURTAIN AIR BAG MODULE

1. Remove the C-pillar trim.

(See

C-PILLAR TRIM REMOVAL/INSTALLATION

2. Remove the D-pillar trim.

(See

D-PILLAR TRIM REMOVAL/INSTALLATION

3. Disconnect the curtain air bag module connector.
4. Connect the

SST (Adapter harness)

to the curtain air bag module as shown in the figure.

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS Air Bag System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:16:38 AM

Page 31

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды