Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1705 | Manualshive

Страница: 1705 / 2589

background image

Fig. 43: View Of Solar Radiation Sensor

Courtesy of MAZDA MOTORS CORP.

SOLAR RADIATION SENSOR INSPECTION

1. Using a tester, connect the positive (+) lead to solar radiation sensor terminal A, the negative (-) lead to

terminal B or C, then measure the resistance.

z

If the resistance is not normal, replace the solar radiation sensor.

Resistance

except infinity ohms

2. Block the light to the solar radiation sensor, connect the positive (+) lead of a tester to solar radiation

sensor terminal B or C and negative (-) lead to terminal A, then measure the resistance.

z

If the resistance is not normal, replace the solar radiation sensor.

Resistance

infinity ohms (no continuity)

3. Expose the solar radiation sensor to natural sunlight.
4. Using a tester, connect the positive (+) lead to solar radiation sensor terminal B or C, the negative (-) lead

to terminal A, then measure the resistance.

z

If the resistance is not normal, replace the solar radiation sensor.

2008 Mazda CX-9 Grand Touring

2008 HVAC Control System (HVAC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:12:36 AM

Page 26

© 2005 Mitchell Repair Information Company, LLC.

«
...
1703
1704
1705
1706
1707
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Jabra Страницы: 10

Бренд: RAM Страницы: 116

PICASSO XSARA DESIRE 1.6 - MESUREMENT

Бренд: CITROEN Страницы: 2

Бренд: GMC Страницы: 425

Бренд: SnapPad Страницы: 5

BTFREQ PRO BTFMPD3SR

Бренд: Scosche Страницы: 16

Бренд: Porsche Страницы: 313

Бренд: Meta System Страницы: 22

Бренд: Quadratec Страницы: 6

Бренд: Kargo Master Страницы: 9

Бренд: Volkswagen Zubehör Страницы: 40

Бренд: Toyota Страницы: 24

Бренд: Toyota Страницы: 36

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 91

NewMotion Home Advanced 2.1

Бренд: Shell Страницы: 24

Бренд: Skoda Страницы: 319

Бренд: Fishbone Offroad Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды