Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1446

Страница: 1446 / 2589

Fig. 47: View Of Cylinder Head Cover Oil Seal & SST

Courtesy of MAZDA MOTORS CORP.

ENGINE FRONT COVER AND NO.3 ENGINE MOUNT BRACKET REMOVAL NOTE

1. Loosen the engine front cover and No.3 engine mount bracket installation bolts in the order shown in the

figure.

2. Install 4 of the engine front cover bolts (finger tightened) into the 4 threaded holes in the engine front

cover.

Fig. 48: Identifying Engine Front Cover & No.3 Engine Mount Bracket

Courtesy of MAZDA MOTORS CORP.

1. Tighten the bolts one turn at a time in a crisscross pattern until the engine front cover-to-cylinder

block seal is released.

2. Remove the engine front cover.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:57 AM

Page 36

«
...
1444
1445
1446
1447
1448
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды