Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 360

Страница: 360 / 2589

1. Remove the automatic transaxle. (See

AUTOMATIC TRANSAXLE REMOVAL/INSTALLATION

[AW6A-EL, AW6AX-EL]

2. Remove the VSS. (See Automatic Transaxle and Transfer Workshop Manual AW6A-EL, AW6AX-EL)

SOLENOID VALVE INSPECTION [AW6A-EL, AW6AX-EL]

RESISTANCE INSPECTION (ON-VEHICLE INSPECTION)

1. Disconnect the negative battery cable.
2. Remove the air cleaner component. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION

[MZI-3.7]

3. Remove the TCM. (See

TCM REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

4. Measure the resistance between the following terminals.

Fig. 34: Identifying Coupler Component

Courtesy of MAZDA MOTORS CORP.

If there is any malfunction, inspect the coupler component.

If the coupler component is normal, replace the control valve body. (See

CONTROL VALVE

BODY REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

If foreign materials are stuck to the VSS, disturbance by magnetic
flux can cause sensor output to be abnormal and thereby negatively

affect control. Make sure that foreign materials such as iron filings

are not stuck to the VSS during installation.

CAUTION:

Water or foreign material entering the connector can cause a poor

connection or corrosion. Be sure not to allow water or foreign
material on the connector when disconnecting.

Do not damage the terminals.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:30 AM

Page 32

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды