Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2390

Страница: 2390 / 2589

CONNECTOR TERMINAL REFERENCE

2. Connect the battery positive voltage to power window motor terminal D and connect terminal C to

ground.

3. Operate the power window motor and measure the voltage at terminals A and B.

If there is any malfunction, replace the power window motor.

Voltage

Pulse: max. 12 V/min. 0 V

REAR SIDE

1. Apply battery positive voltage and connect the ground to the power window motor terminals, and then

inspect the power window motor operation.

If the power window motor does not operate as indicated in the table, replace it.

Fig. 16: Power Window Motor (Front Side) - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

Operation

Terminal

Open

B+ Ground

Ground B+

CAUTION:

If the power window motor temperature is high, the motor may
not rotate due to the motor internal bimetal function. Leave it

untouched for about 3 min to cool it down, then reinspect.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 11

«
...
2388
2389
2390
2391
2392
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды