Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 455

Страница: 455 / 2589

SHROUD PANEL REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the following parts:

1. Front bumper (See

FRONT BUMPER REMOVAL/INSTALLATION

)

2. Front combination lights (See

FRONT COMBINATION LIGHT

REMOVAL/INSTALLATION

)

3. Front bumper reinforcement (See

FRONT BUMPER REINFORCEMENT

REMOVAL/INSTALLATION

)

4. Ambient temperature sensor (See

AMBIENT TEMPERATURE SENSOR

REMOVAL/INSTALLATION

)

5. Crash zone sensor (See

CRASH ZONE SENSOR REMOVAL/INSTALLATION

)

6. Hood latch (See

HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION

)

3. Put the oil cooler aside.
4. Remove the front crossmember extension. (See

FRONT CROSSMEMBER

REMOVAL/INSTALLATION

5. Remove in the order indicated in the table.
6. Install in the reverse order of removal.

Fig. 24: Identifying Removing Sequence Of Shroud Panel Components & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

UPPER MOUNT RUBBER BRACKET REMOVAL NOTE

1. Remove the upper mount rubber bracket while pressing down the upper mount rubber bracket tab in the

direction of the arrow.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:45 AM

Page 16

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды