Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2389

Страница: 2389 / 2589

POWER WINDOW MOTOR INSPECTION

FRONT SIDE

1. Apply battery positive voltage and connect the ground to power window motor terminals E and F, and

then inspect the power window motor operation.

If the power window motor does not operate as indicated in the table, replace it.

module. If this happens, insert a hand through the speaker

installation hole to engage the drum housing tabs, and install the
power window motor to the drum while supporting the drum housing.

Fig. 15: Identifying Power Window Motor Components & Torque
Specifications

Courtesy of MAZDA MOTORS CORP.

CAUTION:

If the power window motor temperature is high, the motor may
not rotate due to the motor internal bimetal function. Leave it

untouched for about 3 min to cool it down, then reinspect.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 10

«
...
2387
2388
2389
2390
2391
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды