Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 653

Страница: 653 / 2589

Fig. 2: Locating Dust Boot

Courtesy of MAZDA MOTORS CORP.

FRONT DRIVE SHAFT REMOVAL/INSTALLATION

1. Remove the side cover.
2. Remove the front ABS wheel-speed sensor. (See

FRONT ABS WHEEL-SPEED SENSOR

REMOVAL/INSTALLATION

3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.

CAUTION:

Performing the following procedures without first removing the ABS

wheel-speed sensor may possibly cause an open circuit in the
harness if it is pulled by mistake. Before performing the following

procedures, remove the ABS wheel-speed sensor (axle side) and fix it
to an appropriate place where the sensor will not be pulled by

mistake while the vehicle is being serviced.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLES Drive Shaft - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:50:57 AM

Page 2

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды