Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1540 | Manualshive

Страница: 1540 / 2589

background image

Fig. 69: View Of Cap

Courtesy of MAZDA MOTORS CORP.

ACCESSORY SOCKET INSPECTION

1. Connect a tester as shown in the figure and verify that there is continuity.

z

If the continuity cannot be verified, replace the accessory socket.

Fig. 70: Identifying Accessory Socket Terminals

Courtesy of MAZDA MOTORS CORP.

AUXILIARY JACK REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the console cover. (See

CONSOLE COVER REMOVAL/INSTALLATION

.)

3. Disconnect the auxiliary jack connector.
4. Squeeze the tabs of auxiliary jack and pull it outward to remove it.
5. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Entertainment - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:06 AM

Page 40

© 2005 Mitchell Repair Information Company, LLC.

«
...
1538
1539
1540
1541
1542
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Ignition Страницы: 1

Бренд: Triumph Страницы: 86

Бренд: Alpine Страницы: 2

Бренд: Whispbar Страницы: 15

Camaro 12000 1968 Series

Бренд: Chevrolet Страницы: 455

Бренд: Whispbar Страницы: 14

Бренд: Oldsmobile Страницы: 2

Vehicle Asset Communicator

Бренд: I.D. Systems Страницы: 41

Бренд: Draw tite Страницы: 4

Бренд: EFILive Страницы: 25

Бренд: Oldsmobile Страницы: 354

Бренд: Metra Electronics Страницы: 17

Indash 75114-296

Бренд: Panavise Страницы: 2

Бренд: Camcar Страницы: 2

ASENTO EV-EXP18R

Бренд: ADAPT SOLUTIONS Страницы: 25

1997 Park Avenue

Бренд: Buick Страницы: 420

MVM Multi Vehicle Mount MVM-45-05

Бренд: Bracketron Страницы: 4

Бренд: Comtronics Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды