Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 476

Страница: 476 / 2589

Disconnect DSC/RSC HU/CM

connector.

Turn the ignition switch to the

ON position (engine off).

Measure voltage between
DSC/RSC HU/CM terminal AK

(harness-side) and ground.

Is the voltage B+?

Repair or replace the wiring harness for open circuit

between battery positive terminal and DSC/RSC

HU/CM terminal AK, then go to Step 5.

INSPECT PUMP MOTOR
GROUND FOR OPEN CIRCUIT

Turn the ignition switch off.

Inspect for continuity between
DSC/RSC HU/CM terminal B

(harness-side) and ground.

Is there continuity?

Yes Go to the next step.

Repair or replace the wiring harness for open circuit

between DSC/RSC HU/CM terminal B and ground,

then go to Step 5.

VERIFY PUMP MOTOR
OPERATION

Turn the ignition switch off.

Connect the M-MDS to the
DLC-2.

Turn the ignition switch to the

ON position (engine off).

Access PMP_MOTOR active
command modes using the M-

MDS.

Does the pump motor operate?

Yes Go to the next step.

Replace the DSC/RSC HU/CM, then go to the next

step.

(See

DSC/RSC HU/CM

REMOVAL/INSTALLATION

VERIFY TROUBLESHOOTING

COMPLETED

Make sure to reconnect all
disconnected connectors.

Clear the DTC from the

memory.

(See

ON-BOARD

DIAGNOSTIC [DSC/RSC]

Gradually slow down and stop
the vehicle.

Is the same DTC present?

Yes

Replace the DSC/RSC HU/CM, then go to the next
step.

(See

DSC/RSC HU/CM

REMOVAL/INSTALLATION

Go to the next step.

VERIFY AFTER REPAIR

Go to the applicable DTC inspection.

2008 Mazda CX-9 Grand Touring

2008 BRAKES On-Board Diagnostic (DSC/RSC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:50:13 AM

Page 20

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды