Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2144

Страница: 2144 / 2589

DIAGNOSTIC PROCEDURE

DTC B267A - DIAGNOSTIC PROCEDURE

STEP

INSPECTION

ACTION

INSPECT WIRING HARNESS BETWEEN
PLG CONTROL UNIT AND LIFTGATE

LATCH AND LOCK ACTUATOR

Disconnect the PLG control module

connector.

Disconnect the liftgate latch and lock
actuator connector.

Inspect the wiring harness between PLG

control module terminal 3H and liftgate
latch and lock actuator terminal B for an

open circuit/short circuit to ground
system.

Yes Go to the next step.

Repair or replace the wiring harness.

Go to Step 3.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES On-Board Diagnostic (Power Liftgate (PLG) System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:46:08 AM

Page 23

«
...
2142
2143
2144
2145
2146
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды