Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1535

Страница: 1535 / 2589

6. Third-row seat belt lower anchor installation bolt (LH) (See

THIRD-ROW SEAT BELT

REMOVAL/INSTALLATION

7. Trunk side trim (Driver side) (See

TRUNK SIDE TRIM REMOVAL/INSTALLATION

3. Remove in the order indicated in the table.

Fig. 61: Identifying Inverter Components & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

INVERTER INSPECTION

1. Measure the voltage at each terminal.

If the voltage is not as specified in the Terminal Voltage Table, inspect the parts under "inspection
item(s)" and related wiring harnesses.

2. Disconnect the negative battery cable.
3. If the system does not work properly even though the inspection items or related wiring harnesses do not

have any malfunction, replace the inverter.

WARNING:

The AC voltage is extremely high voltage. Be careful when
measuring the voltage.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Entertainment - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:06 AM

Page 35

«
...
1533
1534
1535
1536
1537
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды