Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1509

Страница: 1509 / 2589

Fig. 10: Identifying Audio Amplifier Components & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

AUDIO AMPLIFIER CONFIGURATION

1. Connect the M-MDS to DLC-2.
2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

When using the IDS (laptop PC)

1. Select "Module Programming".

3. Then, select items from the screen menu in the following order.

1. Select "Programmable Module Installation".
2. Select "AM".

4. Perform the configuration according to the directions on the screen.
5. Retrieve DTCs by the M-MDS, then verify that there is no DTC present.

If a DTC (s) is detected, perform the applicable DTC inspection. (See

DTC TABLE [AUDIO

AMPLIFIER]

Fig. 11: Identifying Data Link Connector 2

Courtesy of MAZDA MOTORS CORP.

NOTE:

Use the IDS (laptop PC) because the PDS (Pocket PC) does not support
the AUDIO AMPLIFIER CONFIGURATION.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Entertainment - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:05 AM

Page 9

«
...
1507
1508
1509
1510
1511
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды