Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 611

Страница: 611 / 2589

1. Assemble in the order indicated in the table.

could become inoperative. If the rear differential unexpectedly

rotates it could cause injury, therefore do not maintain the rear
differential in a tilted condition. When turning the rear differential,

grasp the rotation handle firmly.

NOTE:

Clean away the old sealant before applying the new sealant.

Install the rear cover within 10 minutes after applying sealant.

Allow the sealant to set at least 30 minutes after installation before filling

the differential with the specified oil.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLES Differential - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:52:15 AM

Page 18

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды