Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 910

Страница: 910 / 2589

DIAGNOSTIC PROCEDURE

DTC P0053, P0054, P0059, P0060 (MZI-3.7) DIAGNOSTIC PROCEDURE

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA

HAS BEEN RECORDED

Has FREEZE FRAME DATA been
recorded?

Yes Go to the next step.

Record FREEZE FRAME DATA on the repair

order, then go to the next step.

VERIFY RELATED REPAIR

INFORMATION AVAILABILITY

Verify related Service Bulletins

and/or on-line repair information
availability.

Is any related Service Bulletins

available?

Yes

Perform repair or diagnosis according to the

available Service Bulletins.

If the vehicle is not repaired, go to the next
step.

Go to the next step.

INSPECT FOR POWER SUPPLY IN
WIRING HARNESS

Disconnect the suspect HO2S
connector.

Perform the KOEO self-test.

Measure the voltage between the

suspect HO2S connector terminal A
and C, on the wiring harness side.

Is the voltage more than 10 V?

Yes Turn the ignition switch off. Go to the next step.

No Repair or replace suspected part, then go to step 9.

INSPECT HO2S HEATER FOR
SHORT TO GROUND

Disconnect the PCM.

Measure the resistance between
HO2S connector terminal A, the

wiring harness side, and body
ground.

Yes Go to the next step.

Repair or replace suspected part, Go to Step 9

2008 Mazda CX-9 Grand Touring

2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:08:34 AM

Page 46

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды