Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1249

Страница: 1249 / 2589

DTC P2122 [MZI-3.7]

DTC P2122 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES

Is the PENDING CODE for the DTC

present?

Go to the next step.

VERIFY AFTER REPAIR PROCEDURE

Perform "AFTER REPAIR

PROCEDURE". (See

AFTER REPAIR

PROCEDURE [MZI-3.7]

Are any DTCs present?

Yes Go to the applicable DTC inspection. (See

DTC TABLE [MZI-3.7]

Troubleshooting completed.

DTC P2122

APP sensor No.1 circuit low input

DETECTION

CONDITION

APP sensor No.1 is out of self-test range low.

POSSIBLE CAUSE

Short to ground circuit between APP sensor terminal F and PCM terminal

1BA

Short to ground circuit between APP sensor terminal D and PCM terminal
1Y

Short to ground circuit between APP sensor terminal G and PCM terminal 1

Short to ground circuit between APP sensor terminal C and PCM terminal
1AH

Short to ground circuit between APP sensor terminal E and PCM terminal

1AK

Connector or terminal malfunction

APP sensor malfunction

2008 Mazda CX-9 Grand Touring

2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:08:42 AM

Page 385

«
...
1247
1248
1249
1250
1251
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды